Protecting Autoworkers From Back And Shoulder Injury By Tilting Cars On The Assembly Line
That's the finding of two recent studies, which tested two ways to protect autoworkers from injury.
Sitting on a cantilevered chair reduced the stress on the workers' backs and shoulders for three common installation tasks. But a different strategy - tilting a car sideways on a carriage so that workers could access the interior while standing - reduced the stress for nine different tasks.
The chair study appears in the July issue of the journal Applied Ergonomics and the carriage study appears in a previous issue.
The car carriage appears to be a better overall option for preventing injuries, explained William Marras, professor and Honda Endowed Chair in the Department of Integrated Systems Engineering at Ohio State University.
"Under these conditions, if you can tilt the car, the chair becomes unnecessary," said Marras, who directs Ohio State's Center for Occupational Health in Automotive Manufacturing (COHAM), where the tests took place.
Honda Motor Co. asked the COHAM team to test the commercially available chair as well as the car carrier, both of which are already used in some of its plants and by other manufacturers around the country.
To use the chair, workers sit on a padded seat at the end of an L-shaped steel beam that is locked into a track above. The "L" slides back and forth as workers use their legs to pull the chair across the floor and into the car.
The researchers tested 10 men and women, five of whom were experienced autoworkers. The other five were college student volunteers, intended to represent first-time, untrained autoworkers. They rode the chair into and out of a car frame while they tightened bolts and installed seat belts, shoulder slides, roof consoles, and dome lights. Wired with sensors to monitor muscle strain, the subjects performed these tasks over a simulated eight-hour workday.
In only three situations - installing the roof console and insulation and tightening bolts in the center of the car - did sitting in the chair reduce loads on the spine and shoulder stress.
The chair didn't help much when workers had to reach the sides or back of the car, either. For installation tasks at the edge of the vehicle, sitting in the chair reduced spine load but did nothing to reduce shoulder stress.
"We thought that sitting down inside the car would make installing the seatbelt easier, but it turned out that you'd need two right hands," said Sue Ferguson, senior research engineer at COHAM and lead author of the study.
Originally, the cantilever chair came with a bucket seat that prevented workers from moving freely. The researchers replaced it with a flat seat and simplified the cantilever system overall. The new design was more practical than the original, and much less expensive: it cost $4,000 to build compared to the original's $100,000.
In the car carriage study, the researchers had 12 people install equipment in a car's interior, underbody, and engine room while standing. They measured stresses on the people's bodies when the car was tilted at different angles.
Of nine different installation tasks, seven became much less strenuous when the car was tilted on its side 45 degrees. The other two showed similar improvements when the car was tilted completely sideways at 90 degrees.
Because of the modification that the researchers made to the seat in the chair study, they began to think about ways to improve seats in general. They are now working with a seat manufacturer to discover more features that make a seat comfortable and functional.
Meanwhile, Honda is using the Ohio State team's discoveries to improve the ergonomics of their factories. In 2007, the company reported that it was able to reduce injuries by 70 percent over five years by adopting these strategies.
Written by Pam Frost Gorder
Ohio State University
Source: EurekAlert!, the online, global news service operated by AAAS, the science society
Please use one of the following formats to cite this article in your essay, paper or report:
Ohio State University. "Protecting Autoworkers From Back And Shoulder Injury By Tilting Cars On The Assembly Line." Medical News Today. MediLexicon, Intl., 16 May. 2012. Web.
25 Jun. 2017. <http://www.medicalnewstoday.com/releases/245395.php>
Ohio State University. (2012, May 16). "Protecting Autoworkers From Back And Shoulder Injury By Tilting Cars On The Assembly Line." Medical News Today. Retrieved from
Please note: If no author information is provided, the source is cited instead.
Contact our news editors
For any corrections of factual information, or to contact our editorial team, please see our contact page.
Copyright Medical News Today: Excluding email/sharing services explicitly offered on this website, material published on Medical News Today may not be reproduced, or distributed without the prior written permission of Medilexicon International Ltd. Please contact us for further details.